收藏本站
MeshConnect? Module Series
PROCESSING
Recommended Reflow Profile
Parameters Values
Ramp up rate (from Tsoakmax to Tpeak)
Minimum Soak Temperature
Maximum Soak Temperature
Soak Time
TLiquidus
Time above TL
Tpeak
Time within 5o of Tpeak
Time from 25o to Tpeak
Ramp down rate
3o/sec max
150oC
200oC
60-120 sec
217oC
60-150 sec
250oC
20-30 sec
8 min max
6oC/sec max
Achieve the brightest possible solder fillets with a good shape and low contact angle.
Pb-Free Soldering Paste
Use of “No Clean” soldering paste is strongly recommended, as it does not require cleaning after the soldering process.
Note: The quality of solder joints on the castellations (‘half vias’) where they contact the host board should meet the appropriate IPC Speci-
fication. See IPC-A-610 " Acceptability of Electronic Assemblies, section 8.2.4 Castellated Terminations.”
Cleaning
In general, cleaning the populated modules is strongly discouraged. Residuals under the module cannot be easily removed
with any cleaning process.
? Cleaning with water can lead to capillary effects where water is absorbed into the gap between the host board and
the module. The combination of soldering flux residuals and encapsulated water could lead to short circuits between
neighboring pads. Water could also damage any stickers or labels.
? Cleaning with alcohol or a similar organic solvent will likely flood soldering flux residuals into the two housings, which
is not accessible for post-washing inspection. The solvent could also damage any stickers or labels.
? Ultrasonic cleaning could damage the module permanently.
The best approach is to consider using a “no clean” soldering paste and eliminate the post-soldering cleaning step.
Optical Inspection
After soldering the Module to the host board, consider optical inspection to check the following:
? Proper alignment and centering of the module over the pads.
? Proper solder joints on all pads.
? Excessive solder or contacts to neighboring pads, or vias.
Repeating Reflow Soldering
Only a single reflow soldering process is encouraged for host boards.
Wave Soldering
If a wave soldering process is required on the host boards due to the presence of leaded components, only a single wave
soldering process is encouraged.
Page 13
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ZICM2410P0-1C-SN MODULE 802.15.4 U.FL CONN
ZICM2410P0-KIT2-1 EVALUATION KIT FOR ZIC2410
ZICM357P2-KIT1-1 KIT DEVELOPMENT ENGINEER EM357
ZLNB1001N8TC IC MUX CTLR TONE/POLARITY 8SOIC
ZLNB100X8TC IC CTRLR DUAL POLAR SWITCH 8MSOP
ZLNB101X8TC IC CTRLR DUAL POLAR SWITCH 8MSOP
ZLNB2006Q20TC MUX DUAL DUAL H/V TONE SW 20QSOP
ZLNB2012Q16TC MUX DUAL DUAL H/V TONE SW 16QSOP
相关代理商/技术参数
ZICM2410P0-1 功能描述:Zigbee/802.15.4模块 Mesh Connect Module 5mW PCB Trace Ant RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
ZICM2410P0-1-B 功能描述:Zigbee/802.15.4模块 Mesh Connect Module 5mW PCB Trace Ant RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
ZICM2410P0-1C 功能描述:Zigbee/802.15.4模块 Mesh Connect Module 5mW U.FL Conn Ex Ant RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
ZICM2410P0-1C-B 功能描述:Zigbee/802.15.4模块 Mesh Connect Module 5mW U.FL Conn Ex Ant RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
ZICM2410P0-1C-SN 功能描述:Zigbee/802.15.4模块 20dBm OP u.FL Conn SNAP Software RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
ZICM2410P0-1C-SN-B 功能描述:Zigbee/802.15.4模块 20dBm OP u.FL Conn SNAP Software RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
ZICM2410P0-1-SN 功能描述:Zigbee/802.15.4模块 6dBm OP Trace Ant. SNAP Software RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
ZICM2410P0-1-SN-B 功能描述:Zigbee/802.15.4模块 6dBm OP Trace Ant. SNAP Software RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm